¡y4G LTE /3G UMTS WCDMA/2G GSM Network Test Equipment& Protocol Analyzer ¡z
¡yBluetooth /Bluetooth Smart /Wi-Fi/USB/PCIE/ Ethernet/NFC/ SD/SDO/eMMC Protocol Analyzer ¡z
Wireless Sensor Network(Ubiquitous Sensor Network)
Smart Home Solutions
ZigBee/ 802.15.4 Solution
Bluetooth/802.15.1 Solution
RFID Solutions
GPS( Global Position System System) Develop equipment
Microwave develop Equipment
Wireless communication & RF Equipment
Intelligent Robot
Fiber Optic Communications Test equipments
Test & Measurement / Electric/Power monitor Instruments
Mobile Communication

 Home > ¡yBluetooth /Bluetooth Smart /Wi-Fi/USB/PCIE/ Ethernet/NFC/ SD/SDO/eMMC Protocol Analyzer ¡z > ¡yITIC¡¦s 1480A USB 2.0 Protocol Analyzer with OTG decoding¡z


No : 1480A
Name : USB 2.0 Protocol Analyzer with OTG decoding
¡DITIC 1480A USB 2.0 Protocol Analyzer with OTG decoding is specifically designed for the road-warrior. It will easily slip into your coat pocket or laptop bag for those trips where bringing a large USB analyzer is not convenient. The physical format is very small, only slightly larger than a pen or a computer mouse. The enclosure is made out of very high-quality brushed aluminum.
¡DThe data captured is in real-time transferred to the Analysis PC where it is analyzed and displayed by the PC Software. The USB Analyzer has no limitation of the data size captured as data is streamed in real-time directly from the link under test into the PC application's tree view display. This allows you to capture many hundreds of MB of data (only limited to the size of RAM in your analysis PC).
¡DThe 1480A contains a 32MB FIFO buffer SDRAM that smooths out bursty traffic such that temporarily bursty traffic on the link under test will not cause the USB Analyzer-to-Analysis PC link to be saturated. The sustained maximum capture speed to the analysis PC largely depends on the speed of the capture PC. As a rule of thumb, as long as the throughput on the link under test is under 15 MB / s then the analysis PC will keep up with the captured data speed without the buffer FIFO filling up. Note that the 1480A USB Analyzer will never lose captured data (regardless if the link under test is saturated) since the captured data is always buffered in the SDRAM FIFO before being sent to the analysis PC.
¡DWell designed and manufactured by ITIC in U.S.A.
¡D: USB 1.0, USB 1.1, USB 2.0, OTG 1.3.
¡D: Automatically detects device connection in high speed (480 Mbps), full speed (12 Mbps), and low speed (1.5 Mbps). (Note: HS Devices are initially connected as FS devices. Only after successfully having completed the Device and Host Chirp Sequences do HS-capable devices enter HS mode. The 1480A fully supports automatic detection of both Device and Host Chirp.)
¡D: Unlimited. Only the available disk and memory of the Analysis PC limits how much data can be captured and analyzed.
¡D: USB 2.0 Type "B" Connector
¡D: USB 2.0 Type "A" and "B" Connectors.
¡D: (1).Host Power: Indicates when the 1480A unit is powered and the Analysis PC Device Drivers have been installed.(2)Link Power: Indicates that the Link Under Test is powered by the Host.(3)Link Activity: Indicates when link activity is detected.
¡D: All bus activity down to the smallest detail is captured and stored into the .usb file when recording. The 1480A Software displays all the captured information from the lowest link level up to the highest protocol level. In addition the VBus voltage is continuously monitored and stored in the capture file.
¡D: LS Device Connection, FS Device Connection, HS Device Connection, Device Reset, Device Chirp, Host Chirp, Device Disconnection, HS Idle, Keep-Alives, OTG Session Request Protocol, OTG Host Negotiation Protocol and OTG VBus events.
¡D:. SETUP Transaction, IN Transaction, OUT Transaction, PING Transactions, SPLIT Transactions.
¡D Device Descriptor, Configuration Descriptor, Interface Descriptor, Endpoint Descriptor, String Descriptor, Device_Qualifier Descriptor, Other_Speed_Configuration Descriptor and OTG Descriptor.
¡D: (1)Token Packets: PID and CRC-5 errors are flagged as invalid.(2)Data Packets: CRC-16 errors are flagged as invalid
¡D: which makes it fully programmable with each new software upgrade.
¡DAllows to fully remotely deploy logic and software upgrades if needed. This means that you will never need to send your hardware to us for upgrade as more advanced software like class decoders are purchased.
¡DThe PC Analysis Software displays data as it is received from the USB Analyzer hardware so you will not have to wait for lengthy data decoding before you can start analyzing the captured data.
¡DAs USB Transactions and Packets are captured, they will be decoded and added to the tree view in the PC Analysis software. This makes it very easy to understand the sequence of events in the captured data.
¡DDetail views display the details for selected Transactions and Packets in the tree view as they are clicked on. The PC Analysis software also decodes payload data in hex format and displays it in the hex view pane.
¡D: 32-bit (x86) and 64-bit (x64) Windows versions (XP SP2 or newer). Pentium 4 or faster CPU is recommended.